Perfection in Series – for more Efficiency
Stallkamp submersible motor pumps are the result of experience and consistent development. They run reliably and safely, are powerful, eff ective and eco-friendly at the same time.
Our Submersible Motor-Pump at a glance
- Electric motor 4,0 – 22,0 kW
- Three-phase-motor 400 V, 50Hz, 1450 - rpm.
- IP68 protection category, insulating category F = 155° C
- Thermo control for each phase as overheating protection
- Motor housing in 1.4301 stainless steel
- Pump housing made from cast iron material coated with 2 component plastic lacquer
- Large pump housing and therefore resistant to blockages
- Pump impeller with intake auger and chopping mechanism with tungsten carbide wear protection
- Galvanized steel suction plate with cutting edges and winding protection
- Sealed with radial shaft seal rings on special acidresistant hardened rings
- Electric cable with waterblocking devices in the longitudinal direction of the cable for moisture protection;special PU outer sheathing with moulded connection
- 1.4301 stainless steel slide bearing and absorb fl ange
- Electric switch as a manual star-delta or automatic star-delta starter with motor protection switch and CEE plug
Useable for pumping
- Manure in repositories, mixing tanks and slurry channels
- Biomass for biogas systems
- Sewage sludge in wastewater treatment plants
- Industrial wastewater in industrial systems
- Top performance under tough conditions (application in manure and biogas plants)
- Spiral shaped shearing edge and large volume housing to prevent blockages
- Thermo-control is installed as standard to prevent damage from overheating
- Pumping medium temperature up to 50° C
- The smooth design prevents the accumulation of fibrous materials
- Space-saving design
- A wide range of accessories
| Type | Motor Power | Start-Up | Nominal Current | Required Protection | Number og Revolutions | Maximum Pressure | Flow Rate | Weight |
|---|---|---|---|---|---|---|---|---|
| TMP 040 | 4,0 kW | direct | 9,0 A | 16 delay | 1450 rpm | 1,0 bar | 80 m3/h | ca. 120 kg |
| TMP 055 | 5,5 kW | Y/Δ | 11,4 A | 20 delay | 1450 rpm | 0,8 bar | 130 m3/h | ca. 140 kg |
| TMP 075 | 7,5 kW | Y/Δ | 16,0 A | 25 delay | 1450 rpm | 1,2 bar | 180 m3/h | ca. 160 kg |
| TMP 110 | 11,0 kW | Y/Δ | 22,1 A | 32 delay | 1450 rpm | 1,5 bar | 312 m3/h | ca. 180 kg |
| TMP 170 | 17,0 kW | Y/Δ | 33,0 A | 50 delay | 1450 rpm | 1,9 bar | 354 m3/h | ca. 190 kg |
| TMP 220 | 22,0 kW | Y/Δ | 43,0 A | 63 delay | 1450 rpm | 2,3 bar | 408 m3/h | ca. 200 kg |
| Type | A | B | C | D | E | F | G | Ball Gangway |
|---|---|---|---|---|---|---|---|---|
| TMP 040 | 665 mm | 210 mm | 242 mm | 700 mm | 275 mm | 392 mm | 410 mm | Ø22 mm |
| TMP 055 | 680 mm | 210 mm | 257 mm | 700 mm | 275 mm | 392 mm | 410 mm | Ø35 mm |
| TMP 075 | 715 mm | 210 mm | 292 mm | 700 mm | 275 mm | 392 mm | 410 mm | Ø35 mm |
| TMP 110 | 710 mm | 245 mm | 286 mm | 800 mm | 320 mm | 475 mm | 500 mm | Ø43 mm |
| TMP 170 | 755 mm | 245 mm | 331 mm | 800 mm | 320 mm | 475 mm | 500 mm | Ø43 mm |
| TMP 220 | 820 mm | 245 mm | 396 mm | 800 mm | 320 mm | 475 mm | 500 mm | Ø43 mm |
The flow rate (volume flow rate in m³) is dependent on the density and viscosity of the liquid, the type and the DM content of the manure (animal feed), the support height and distance and the diameter of the pipeline.
